Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
First of all, before using the liquid silicone feeder, it is necessary to ensure that the relevant parts of the equipment are intact. Check whether the pump, pipe, filter, stirrer and other parts of the liquid silicone feeder are damaged or worn, and if it needs to be repaired or replaced in time. In addition, it is necessary to check whether the power cord and control system of the device are normal, and ensure that the power supply used meets the requirements of the device.
Secondly, before operating the liquid silicone feeder, it is necessary to be familiar with and understand the operating instructions and operating processes of the equipment. Understand the use method, working principle and structure of the equipment, especially regarding the safe operation and maintenance of the equipment. When using the device, follow the operation process. Do not change or adjust the operation parameters of the device. Otherwise, improper operations may cause accidents.
Next, keep the working environment clean and orderly before using the liquid silicone feeder. Clean the work area to avoid debris accumulation and slippery ground. Ensure that the ventilation around the equipment is good to avoid affecting the health of the operator due to the evaporation of a large amount of liquid silicone. In addition, the operator needs to wear suitable work clothes and safety shoes, and wear personal protective equipment such as protective glasses and masks to prevent liquid silicone from splashing into the eyes or mouth.
Then, when operating the liquid silicone feeder, it is necessary to pay attention to the temperature control of liquid silicone. The temperature of LSR has a great impact on the process effect and equipment operation. During the operation, it is necessary to ensure that the temperature of LSR is within a certain range according to the process requirements and the capacity of the equipment, and make appropriate adjustments and controls. If the liquid silicone temperature is too high or too low, it may affect the conveying and mixing effect, and even cause equipment failure.
In addition, when operating the liquid silicone feeder, it is necessary to regularly check the lubrication and sealing of the equipment. The pump and stirrer parts of the liquid silicone feeder have lubrication points, which need to be lubricated according to the instruction manual to ensure the normal operation of the equipment. At the same time, pay attention to the sealing performance of the equipment, check whether the sealing ring and gasket of the equipment are intact, if there is wear or aging, it needs to be replaced in time to avoid leakage of liquid silicone.
Finally, after the liquid silicone feeder stops running, it is necessary to clean and maintain it in time. Remove the liquid silicone and impurities remaining inside the equipment to keep the equipment clean and hygienic. Check and maintain all parts of the equipment regularly, and repair or replace the faulty parts in time. At the same time, pay attention to the maintenance cycle and methods of the equipment, and carry out regular maintenance and maintenance according to the requirements of the equipment manufacturer to extend the service life of the equipment.
In short, when using liquid silicone feeder, it is necessary to comply with the above precautions to ensure the safety of operation and the normal operation of the equipment. Only according to the instructions for correct operation, keep the working environment clean and orderly, pay attention to the temperature control of liquid silicone, regular
September 02, 2024
September 02, 2024
August 17, 2024
September 13, 2024
Recently, the single frequency of drying has been getting slower and slower. The number of years old has grown, and people have become lazy. As hard-earned gold coins have been deceived by Zhang...
Rotational molding process, also known as rotary molding, rotary casting molding. It is a thermoplastic hollow molding method. The powder is injected into the mold, through the heating of the mold...
1. Precision of mold manufacturing and post-wear factors 2, the plastic parts themselves shrinkage, cooling changes factors (this covers more aspects, mold flow analysis is a very deep knowledge) 4,...
Vertical injection molding machine - insert molding (insert molding) refers to the injection of resin into the mold after the preparation of the different material inserts, the molten material and...
Email to this supplier
September 02, 2024
September 02, 2024
August 17, 2024
September 13, 2024